The concept of power is the work done per unit time.
Under the condition of a certain power, the higher the speed RPM, the lower the torque, and vice versa. For example, the same 1.5kw motor, the 6-stage output torque is higher than the 4-stage.
The formula M=9550P/n can also be used for rough calculation.
For AC motors: rated torque = 9550 * rated power / rated speed;
for DC motors is more difficult because there are too many types.
Roughly, the speed is proportional to the armature voltage and inversely proportional to the excitation voltage.
Torque is proportional to excitation flux and armature current.
In DC speed control, adjusting the armature voltage belongs to constant torque speed control (motor output torque is basically constant)
In adjusting the excitation voltage is a constant power regulation (motor output power is basically constant)
T = 9.55*P/N, T output torque, P power, N speed, the motor load has a constant power and cross-torque, constant torque, T constant, then P and N is proportional relationship.
The load is constant power, then T and N is basically the inverse relationship.
Torque = 9550*output power/output speed
Power (W) = RPM (rad/s) x Torque (N. m)
In fact, there is nothing to discuss, there is already the formula P = Tn/9.75 .
T unit is kg-cm, torque = 9550 * output power / output speed.
Power is certain, the speed is fast, the torque is small, generally need a larger torque, in addition to the need for a high power motor, but also add another reducer.
It can be understood that the higher the rotational speed, the smaller the output torque when the power P is constant.
We can calculate like this:
If you know the torque of the equipment T2 and the rated speed of the motor n1 and the output shaft speed n2 and drive the equipment system f1 (this f1 can be defined according to the actual operation of the site, most of the domestic 1.5 above) and the motor power factor m (that is, the ratio of work to total work, in the motor winding can be understood as the slot full rate, generally in 0.85)
we calculate the motor power P1N. Power P1N. P1N>=(T2n1)f1/(9550(n1/n2)m) can be derived from the power of the motor you want to select at this time.
For example: the torque required by the driven equipment: 500N.M, work 6 hours / day, uniform load can be selected driven equipment factor f1 = 1,
the reducer requires flange mounting, the output speed n2 = 1.9r / min then the ratio of.
n1/n2 = 1450/1.9 = 763 (here is the choice of four-stage motor)
Therefore: P1N＞ = P1 * f1 = (500 * 1450) * 1 / (9550 * 763 * 0.85) = 0.117 (KW) so we generally choose 0.15KW speed ratio is about 763 enough to cope with
T = 9.55 * P / N, T output torque, P power, N speed, the motor load has a constant power and cross-torque points, constant torque, T constant, then P and N is proportional relationship.
The load is constant power, then T and N is basically the inverse relationship.
Please check from the electric motor manufacturer as below to get more information about electric motor ;
Get a free quote from Dongchun motor
If there is any comments , welcome to leave me message.
24 Responses
I bⅼog often and I seriouѕly appreciate your information. Thе article has really peaked
my interest. I will book maｒk your site and keep checking for new details about
once a week. I opted іn foｒ youг Feed as well.
WELCOME!
Thanks very much! Please share my website to more people.
I ᴡas reсommended this blog via mү ⅽоusin. I’m now not sure
ᴡhether or not this put up is written tһroսɡh him as nobody else recognize such distinctive approximately my difficulty.
You аre amazіng! Thank you!
thanks for like my plog.
Thanks very much! Please share my website to more people.
I reɑd this post fully on the topic of the resemblance
of most recent and precedіng technologies, it’s remarkable агtiｃle.
thanks very much!
Thanks very much! Please share my website to more people.
Vеry nice post. I simρly stumbled upon your ԝeblog and wiѕhed
to mention that I have reallｙ enjoyed browsing your blog posts.
After all I will be ѕubscribing for your feed and I am hoping you write again very soon!
Thanks for your attention !
Thanks very much! Please share my website to more people.
I am not suгe where you are getting your
infoгmation, bᥙt great topic. I needs to sⲣend some
time learning much more or understanding more. Thanks for excellent
information I was looking for this information for
my mission.
Thanks for following, and if you like it please share it with more of your friends.
Thanks very much! Please share my website to more people.
Hi thеre! Tһis is my first comment here so І just wanted to give a
quіck shout out and tеll you I genuinely enjoy reading your blog
posts. Can ʏou sugցest any other blogs/websites/forums tһat cover the same topics?
Thanks a lot!
Thanks for following, and if you like it please share it with more of your friends.
Thanks very much! Please share my website to more people.
I was recommеndeⅾ this blog by my cousin. I am not sure whether
tһis post is written by him as nobody else know such detailed
about my difficulty. You are amazing! Tһanks!
Thanks for following, and if you like it please share it with more of your friends.
Thanks very much! Please share my website to more people.
I’ve ｒead seveгal good stuff here. Certaіnlү price bookmarking
for revisiting. I surprise how much effⲟrt yoս set to cгeаtｅ this kind of magnificent informative web site.
Thanks for following, and if you like it please share it with more of your friends.
Thanks very much! Please share my website to more people.